In this study, the frequency and spatial properties of undesired electromagnetic radiation distribution around a simple printed circuit board (PCB) model, which only has the mismatching printed line (PL) and ground, are estimated. Finite difference time domain (FDTD) modeling is developed for the analysis space, which is 500 400 51 mm3 in size, around the PCB. As the driving clock pulse has a very wide frequency bandwidth, ranging from kHz to GHz, basic and precise investigation of the noise emission mechanism from the basic model is performed. The results of the magnetic field Hx on the PCB as determined by FDTD simulation, and those of the experiment, driven by a clock pulse, agree well. The results show that although this approach is basic and simple, it becomes clear that the frequency and spatial characteristics of the electric and magnetic field near the PCB are influenced by the wavelength of the frequency and appling the driving clock pulse, and the low-frequency component of the electromagnetic distribution around the PCB is larger than the high-frequency components. It is suggested that the low-frequency noise problem should be carefully considered.

The effects of Gaussian electromagnetic noise and non-Gaussian one on TV picture degradation are studied by using a composite noise generator which can control noise parameters. Three kinds of still pictures and four kinds of motion pictures are tested, and the picture degradation is subjectively evaluated with five-grade impairment scale. The tendency of the picture degradation against the every picture is almost the same. But MOS (Mean Opinion Score) between still picture and motion picture degradation is different in some measure when the power of burst noise is small.

Arc discharge generated by breaking electrical contact is considered as a main source of not only degradation of the electrical property but also an undesired electromagnetic (EM) noise. In order to clarify the effect of heated temperature on the bridge, arc-duration and the fluctuation of voltage, opening-waveforms at slowly separating silver-tin dioxide contact with holder heating are measured and discussed experimentally in this paper. Firstly, opening-waveforms are measured. Secondly, voltage fluctuation of the each arc-phase is discussed to extract the effect of the heated holder. The relationship between temperature of the heated holder and duration and fluctuation of the arc was investigated experimentally. It was revealed that as the initial temperature of the heated holder becomes higher, arc-duration becomes slightly longer. In addition, voltage fluctuation at the gaseous-phase decreases when the holder is heated. Consequently, the heated holder can suppress the voltage fluctuation even if its duration becomes slightly longer.

To clarify the transmission characteristics and near magnetic field on the angle pattern for the parallel transmission lines, the authors investigate how influence the angled pattern on the transmission lines by experiment and calculation. The angled patterns on the transmission lines are straight, right angle and curve. It shows that the suppression of EMI radiation at the angled pattern on the parallel transmission lines of the magnetic head is essential. In addition, it is suggested that angle pattern might be one of cause for the signal distortion and specific EMI radiation at high frequency.

This paper presents a possibility of Electromagnetic (EM) analysis against cryptographic modules outside their security boundaries. The mechanism behind the information leakage is explained from the view point of Electromagnetic Compatibility: electric fluctuation released from cryptographic modules can conduct to peripheral circuits based on ground bounce, resulting in radiation. We demonstrate the consequence of the mechanism through experiments where the ISO/IEC standard block cipher AES (Advanced Encryption Standard) is implemented on an FPGA board and EM radiations from power and communication cables are measured. Correlation Electromagnetic Analysis (CEMA) is conducted in order to evaluate the information leakage. The experimental results show that secret keys are revealed even though there are various disturbing factors such as voltage regulators and AC/DC converters between the target module and the measurement points. We also discuss information-suppression techniques as electrical-level countermeasures against such CEMAs.

In this paper, to clarify the thermal effect of the bridge for long lifetime contacts, the effects of heat conductivity on bridge break at different material contact pairs were discussed experimentally. To examine the relationship between the bridge and material, the electrode materials of the anode and the cathode were chosen as the same and the different material pairs in this experiment. Ag, AgPd60 and Pd were chosen as the electrode materials, because Ag, AgPd60 and Pd had the different thermal diffusivity. Firstly, the voltage waveforms in the bridge with different material pair were compared to the voltage waveform with the same material pair case. Secondary, the effects of heat conductivity on the break of bridge were discussed. In the results, the bridge voltage waveform depends on the electrode material at anode side. The length of the bridge at bridge break depends on the heat conductivity of the electrode material at anode side. This study provides the basic considerations on the thermal condition of the bridge break.

When contact failure occurs in a connector in a coaxial high-frequency (HF) signal transmission line, it is well known that common-mode (CM) radiation occurs on the line. We focus on contact conditions in a connector causing such CM radiation. Experiments and simulations verify that CM radiation increases as the contact resistance increases. While the CM current strongly depends on the distribution pattern of contact resistances at a low resistance, the CM current does not depend on these pattern at a high resistance. Our results indicate that it is important to maintain a symmetrical distribution of contact spots whenever the number of such spots is four or more.

A cascode type AM modulator, which is the combination of a static induction transistor (SIT) and a JEFT is proposed. The experimental results show the improvement in linearity and distortion because of the good constant voltage characteristics of SIT.

As the basic study of the electromagnetic interference (EMI) problem at the circuit elements, the near magnetic field distributions above resistors for the termination of a transmission line are measured to reveal the profile of radiation. Five kinds of resistors and two types of resistance values are sampled. The results showed that the variation of the near magnetic field distribution above the transmission line is effected largely by the reactance of the resistor at the high frequency. These results are the basis for the design of the structure of the component.

Various approaches on optical network systems using wavelength-division multiplexing (WDM) technique have been proposed. It is difficult to make a scale of WDM network larger since a number of the optical wavelength which can be used is limited. In order to make easily larger scale of network, multi-hop WDM network have been proposed. We have studied 2-hop network: RookNet which has simple routing algorithm and high network throughput. Nodes in RookNet are divided into row groups and column groups and are placed in a mesh form. Packets are transferred between nodes over 1-hop or 2-hops. The 2-hop transfer means that a source node sends packets to a destination node via a relay node. When 2-hop traffic increases, relay processing time in a relay node is increasing. This is the reason that network throughput becomes low. To solve this problem is very important. In this paper, we show RookNet rearrangement algorithm which replaces location of node within group so as to decrease the 2-hop traffic and to maintain high network throughput. Proposed rearrangement algorithm can achieve improvement of 10 percent in terms of throughput. We also propose RookNet configuration which discriminates optical wavelength and subcarrier effectively in order to decrease the relay processing time.

The effect of the structure with difference on cross-section for the enlarged models that simulates signal transmission line (STL) in the magnetic head of HDD is discussed. The experimental results suggested that strip and shield structure are effective for suppression of EMI.

The spatial distribution of the electric field in the low to high frequency bands radiated from printed circuit board (PCB) should be estimated continuously from near to far field. The characteristic of the electric field distribution is analyzed by the FDTD-multiple analysis space (FDTD-MAS) method, which can analyze from near to far field continuously, and compared with measured results. Since the analyzed electric field distribution is good agreement with measured results, it is suggested that the continuous distribution for electric field from near to far field can be calculated by the FDTD-MAS method. The electric field at low frequency is larger than that at high frequency within 1 m.

In this paper, the separation of heat generation and heat transfer related to temperature rise of silver palladium contact was investigated experimentally in order to predict the temperature rise of contact by the use conditions such as voltage range between 25 to 40 V, current range between 3.2 to 5.0 A and silver palladium alloy (AgPd) materials. Firstly, relationship between temperature rise of contact and supply power was discussed. The effects of heat generation and heat transfer on temperature rise were separated and quantified by least squares method. Secondly, effects of durations and integral powers of bridge and arc on temperature rise were also discussed by changing supply power. Results show that the integral power of the bridge increases when supply power increases. As the supply power increases, integral power of arc also increases. The temperature rise is dominated by integral power of bridge. Remarkable difference of bridge duration can not be seen in the five materials (AgPd30, AgPd40, AgPd50, AgPd70 and Pd). The supply power is increased, arc duration gets longer. As weight percent of Pd content increases, the effect of supply power on arc duration becomes larger. Consequently, the integral power of arc increases. This study is a basic consideration to realize methods predicting temperature rise of contact.

EMI coupling paths in an electronic controller are investigated experimentally. Common-mode current measurements on the attached cable are used for diagnosing changes made to the EMI coupling path. Experiments that include shielding various portions of the PCB, and re-routing high-speed traces are conducted to characterize the coupling path. A means of identifying and characterizing EMI coupling paths in functioning hardware, and relating them to design features, is demonstrated.

Negative group delay characteristics can be used to improve signal-integrity performance such as equalizer for compensation of the group delay of transmission line (TL). This brief-paper newly attempts to propose a concept of the embedded Folded-Stepped Impedance Resonator (F-SIR) structure with open-stub resonator, for negative group delay and slope characteristics at high-frequency as well as low-insertion loss. The concept of the proposed TL is based on the combination of resonance and anti-resonance due to open-stub resonator in order to establish wideband negative group delay and negative slope characteristics. The proposed TL is fabricated on PCB, and then the concept is validated by measurement and simulation.

By the derivative expansion method we solved a certain perturbation problem which well represents the phase lock loop. We derived the equation which describes the dynamics of a slowly varying parameter E, where E can be regarded as the averaged energy of the system approximately.

It is necessary to know how the contact voltage and contact area vary with time to clarify the physics of contact lifetime and contact resistance. In this paper, to clarify the effect of the heating value on the diameter of the contact area, the variations of the contact voltage and contact diameter with time are measured at a low-speed breaking contact near the thermal equilibrium condition under which a stable bridge is generated. The effect of the heating value on the relationship between the contact diameter and the length of the bridge at breaking is also discussed. In the results, the contact voltage waveform was found to be macroscopically proportional to the displacement of the moving electrode lc. On the other hand, the contact diameter dc decreased slightly with increasing lc. At all currents investigated dc decreased when lc increased. The length of the bridge at breaking was increased by increasing the current. A large heating value of the contact area resulted in a long bridge because the volume of the melted metal increases.

Common-mode (CM) current on a feed cable attached to printed circuit board (PCB), which is one of main source of undesired electromagnetic radiation problem, is investigated by experimental and finite-difference time-domain (FDTD) modeling. In this paper, frequency responses of CM current on PCB and feed cable are modeled and analyzed as an electromagnetic interference (EMI) antenna, which depends on the configuration of PCB with a wire cable. Several different configurations are prepared to demonstrate the effect of PCB dimension on resonance frequencies of CM current. In the results, EMI antenna in the frequency band around the first resonance frequency was comprised of the ground plane and cable. In order to explain the frequency response of CM current, two EMI antenna models are proposed and demonstrated. EMI antenna is comprised of the ground plane and cable, and the other EMI antenna is comprised of the trace on the ground plane. It is suggested that the result is one of basic consideration for the ground plane with cable that have high EMI problem and resonance frequency of CM current.

Arc discharge at breaking electrical contact is considered as a main source of not only degradation of the electrical property but also an undesired electromagnetic (EM) noise. In order to clarify the effect of holder temperature on the bridge and arc-duration, opening-waveforms at slowly separating silver-tin dioxide contact with different holder temperature are measured and discussed experimentally in this paper. Firstly, as opening-waveforms, the contact voltage, the contact current and the movement of moving contact related to the gap length are measured simultaneously. Secondly, the relationship between temperature of the holder and duration of the arc was quantified experimentally. It was revealed that as the initial temperature of the holder becomes higher, arc-duration becomes slightly longer. More importantly, the holder temperature dependencies of percentage of each-phase (metallic and gaseous-phases) are different with different closed-current.